Why do the control systems of mobile phone jammers mostly adopt the transmission method of wired connection?

Why do the control systems of mobile phone jammers mostly adopt the transmission method of wired connection?

Due to the need to limit the use of mobile phones in many occasions, installing a mobile phone blocker has become the most effective way to solve this problem. However, users like some schools, prisons, detention centers, etc., their demand for mobile phone jammers is large-scale, and they often need dozens or even hundreds of them. So how to control and manage the large number of shielding devices in a unified way has prompted the synchronous development of the mobile phone shielding device control system. Nowadays, several shielding devices with remote unified centralized management function can be seen on the market. After comparing the product functions and supporting performance, the question arises. Why do the control systems of mobile phone shielding devices mostly adopt the transmission method of wired connection?

At present, in the control system of the current common mobile phone shielding device, the networking mode of multiple shielding devices is almost all connected through wired connection. Multi-core cable for serial protocol networking. In addition, there is another way, which is in the form of power carrier, by means of the power line that supplies power to the mobile phone GPS Jammer, and also transmits the control system while supplying power. But no matter which of the above methods, their communication network is actually through wired connection. So some customers think: Wired connection must require construction and wiring, so is it possible to use relatively mature wireless networking technology to control several mobile phone jammers online?

16 Antenna Full Band Mobile WIFI GPS LOJACK Phone UHF VHF Jammer

Although the biggest advantage of wireless networking is that there is no need to arrange dedicated communication cables, the communication frequency band used in wireless networking is precisely the communication frequency band that needs to be shielded or interfered with the most during the use of our mobile phone jammer, such as 433MHz and WiFi 2.4G, 5.8G, etc., if the wireless connection is used to realize the networking of the control system of the mobile phone jammer, this will cause a very embarrassing result: when the manager remotely opens the phone jammer through the software, because at this time If the signal is not shielded yet, it is normal to turn on the equipment in the system, but once the shielded device is turned on, the wireless communication signal will be interfered by the shielded signal, which will cause the management personnel to carry out the next control command. When sending and transmitting, the signal cannot be reached or the transmission distance is severely shortened. This will also make the whole set of mobile phone jammer control system unstable.

Because of the factors that cause unstable signal transmission analyzed above, most of the control systems used in mobile phone jammers can only use wired connection and networking.

When the mobile phone works, it is within a certain frequency range. The mobile phone and the base station are connected through radio waves to complete the transmission of data and sound with a certain frequency and modulation method. According to this communication principle, the mobile phone signal jammer scans from the low-end frequency of the forward channel to the high-end at a certain speed during the working process. The scanning speed can form the same frequency noise interference in the received message signal of the mobile phone, and the mobile phone cannot detect the normal data sent from the base station, 2G3G4G5G signal, so that the mobile phone cannot establish a connection with the base station. The mobile phone shows phenomena such as searching the network, no signal, and no service. The shielding distance of the mobile phone signal jammer produced by topsignaljammer Co., Ltd. is closely related to the distance of the base station.

First five articles:The most common jamming methods of UAV jammer countermeasure systemThere is a base station in the school, will it affect the shielding effect of the full-band jammer?What is the best way to interfere with the signal jammer in the examination room in the school?Will a signal jamming car make the car remote key fail?Talk about the signal jammer in the examination room Last five articles: Can the car wireless signal jammer realize long-distance wireless remote control?What equipment is needed for the construction survey of the mobile phone signal shielding system project?The importance of spectrum analyzer for the installation and debugging of cell phone signal jammerAnalysis of the advantages and disadvantages of matching directional antennas for vehicle wireless signal jammersIs it possible to destroy drones using drone strike equipment?
Back to blog